|
Posted by Clark on September 6, 2007, 5:50 pm
If you were Registered and logged in, you could reply and use other advanced thread options
flew at my knee, it hit my knee, it cut my knee through my jeans,
it bruised my knee, it hurts, I'm limping.
So I went out and bought one for $12.98 at Tractor Supply, shoulda done that
first.
I don't remember being this dumb when I was younger, but then again I knew
everything when I was younger.
and yes I was sober.......
Yes I thought it was funny too.
Clark
|
|
Posted by on September 6, 2007, 6:52 pm
If you were Registered and logged in, you could reply and use other advanced thread options
> I tried I failed, it was springy I tried to bend it straight, it slipped, it
> flew at my knee, it hit my knee, it cut my knee through my jeans,
> it bruised my knee, it hurts, I'm limping.
>
> So I went out and bought one for $12.98 at Tractor Supply, shoulda done that
> first.
>
> I don't remember being this dumb when I was younger, but then again I knew
> everything when I was younger.
>
> and yes I was sober.......
>
> Yes I thought it was funny too.
> Clark
>
>
Stop it!!! I just peed my pants laughing.
|
|
Posted by Srgnt Billko on September 6, 2007, 8:10 pm
If you were Registered and logged in, you could reply and use other advanced thread options
>I tried I failed, it was springy I tried to bend it straight, it slipped,
>it
> flew at my knee, it hit my knee, it cut my knee through my jeans,
> it bruised my knee, it hurts, I'm limping.
>
> So I went out and bought one for $12.98 at Tractor Supply, shoulda done
> that
> first.
>
> I don't remember being this dumb when I was younger, but then again I knew
> everything when I was younger.
>
> and yes I was sober.......
>
> Yes I thought it was funny too.
> Clark
>
>
I've got a trailer jack with the wheel rusted fast. Wanna take a crack at
freeing it up ? (I just want to watch)
|
|
Posted by Steveo on September 6, 2007, 9:40 pm
If you were Registered and logged in, you could reply and use other advanced thread options > >I tried I failed, it was springy I tried to bend it straight, it
> >slipped, it
> > flew at my knee, it hit my knee, it cut my knee through my jeans,
> > it bruised my knee, it hurts, I'm limping.
> >
> > So I went out and bought one for $12.98 at Tractor Supply, shoulda done
> > that
> > first.
> >
> > I don't remember being this dumb when I was younger, but then again I
> > knew everything when I was younger.
> >
> > and yes I was sober.......
> >
> > Yes I thought it was funny too.
> > Clark
> >
> >
>
> I've got a trailer jack with the wheel rusted fast. Wanna take a crack at
> freeing it up ? (I just want to watch)
>
Haha! Good thing Clark has a sense of humor and a gimp knee.
|
|
Posted by Clark on September 7, 2007, 7:27 am
If you were Registered and logged in, you could reply and use other advanced thread options
>> I tried I failed, it was springy I tried to bend it straight, it
>> slipped, it
>> flew at my knee, it hit my knee, it cut my knee through my jeans,
>> it bruised my knee, it hurts, I'm limping.
>>
>> So I went out and bought one for $12.98 at Tractor Supply, shoulda
>> done that
>> first.
>>
>> I don't remember being this dumb when I was younger, but then again
>> I knew everything when I was younger.
>>
>> and yes I was sober.......
>>
>> Yes I thought it was funny too.
>> Clark
>>
>>
>
> I've got a trailer jack with the wheel rusted fast. Wanna take a
> crack at freeing it up ? (I just want to watch)
Sure, all I need for that fix is, a rubber mallet, a trampoline, a 3lb
sledge hammer, and small amount of fireworks, oh and some axle grease for
the shop floor.
;-)
Clark
|
| Similar Threads | Posted | | New England, Lawn question- Bent grass | August 27, 2008, 3:14 pm |
| 6 Ways Fixing A Decorating Mistake | June 20, 2007, 11:01 pm |
| fixing flats on garden rolling stock | April 2, 2008, 9:46 pm |
| blade | August 6, 2006, 12:32 pm |
| looking for blade | June 25, 2007, 11:26 pm |
| Dethatching blade | March 10, 2006, 9:45 pm |
| lawnmower blade | May 22, 2006, 12:45 pm |
| Blade angle | June 9, 2007, 10:42 am |
| How are you getting at your lawn tractor blade? | May 14, 2008, 10:36 am |
| question about lawnmower blade noise | March 19, 2008, 1:45 am |
|
XML site map